Octo Light TML100.... This Ultra Bright LED light attaches right to your Taig Mill Or Lathe! Fully adjustable, Made using the latest LED & LED Driver technology so the batteries will last for hours. LOOK!

AMERICAN MADE... Yes, Even The LED!

This image was taken with normal room lighting on. A four foot dual tube fluorescent light is less than 4 feet away! 

NOW YOU CAN SEE!

MAKES MATERIAL SETUP EASY!

ADJUSTABLE TO ANY POSITION!

3 MINUTE INSTALL!

Works With Any Taig Mill Or Lathe!

GET YOURS NOW... ON SALE...

ONLY.. $119.95

ER Flycutter.... This great little tool does the same job as the screw on fly cutter. The difference is, this slides right into a 3/8 collet.  Works with any 3/8 collet!! On Any Machine!

Great tool for surfacing off material.

Comes complete, as shown.

Your Cost Only.... $19.75

When set up correctly, this flycutter leaves a near mirror finish. The key is in the depth of cut. Use deep enough cut that the tool can bite the material and not skip across the surface.

ER Drill chuck arbor adapter.

This Adapter makes it possible to attach drill chucks w/ 3/8- 24 thread and other tooling to the new style ER spindles that Taig  now offers. 

Works with any 3/8 collet. Get Yours Today!

Requires 3/8 Collet not included...see our ER collet selection and great prices!

Retail Price... $14.95.....Your Cost Only....$13.85

THIS STEEL MILLING VISE is perfect for any desktop mill or even drill press work. The side slots make it very easy to use clamps to hold the vise onto the machine.

Vise Dimensions: Opens to 2-3/16", Jaw Depth is 15/16". The Jaw Width is 2-3/8".
Total Height of the vise is 1-3/4". Total Body Length is 4-5/16" long. Weight... 3 Lbs.

Order Now! Only.... $129.99

Motor mount bracket withnecessary hardware, fits normal Taig and nema 48 frame motors.

Cheaper Than You Can Make It!..... Stock # 1022

Only...$5.19

This adapter allows you to use ER-16 collets on your mill or lathe if you have the old style spindle. The adapter screws onto your 3/4-16 spindle nose thread. Handy To Have!

Stock # 1045-ER  Only...$25.99

The depth stop is mounted in the spindle and serves as a stop for the work piece while using the 3 jaw or 4 jaw chuck. By using the Depth stop you are able to control the depth at which the work piece is always stopped at. This allows you to chuck up numerous parts while maintaining the same machined depth each time. The stop can be adjusted by loosening the nut in the back and screwing the rod in or out and then tightening the nut again. The 30 degree collet like piece that fits in the spindle is threaded so that the stop rod can be adjusted for the desired depth.

Stock # 1026  Only...$3.95

4 jaw.... 3 1/4" dia. chuck 3/4-16 thread for mounting. The jaws adjust independently. Reversible heat treated steel jaws. NICE!

Stock # 1030

Retail  $64.75....   Only...$63.99

Lathe Dog for holding work piece while turning between centers.

Stock # 1034 Only...$9.35

Face plate 3 1/4 inch dia. with 3/4-16 thread for mounting.

These face plates are perfect for mounting odd shaped material or offset pieces on the Taig Lathe. It screws directly onto the chuck adapter or the lathe spindle nose.

Stock # 1035    Only...$14.75

Stock # 1037-3H

 Only....$10.79 

3-1/4" Face Plate angle bracket set. These can be used with the 1035 face plate for mounting material...or in many other ways. A couple of sets are always handy to have.

Stock # 1036         Only...$5.69 per set.

Stock # 1038

Only...$26.50

Collet Set, 7 collet sizes that will work with the Taig mills or lathe. The sizes are: 1/8,5/32,3/16,7/32,1/4,9/32,5/16.  These are the older style 15 degree collets. 

Stock # 1040. Only...$32.50

Collet Closer (Spindle Nut) Fits both The Taig Mill & Lathe.

This nut is for the older style spindle and does not fit the ER Spindle.

Stock # 1042

 Only...$5.69

Set of 4 blank collets for making special arbors.
Can be bored and slotted. These collets are for the older style spindles. 

Stock # 1043

     Only...$5.38

3 Jaw Chuck...  3- 1/4" Diameter with 3/4-16 mounting threads.
Self centering, steel body, comes with reversible aluminum soft jaws.

Stock # 1050    Retail... $64.10 Only...$63.89

Blank soft jaw set.... Cut into these to match any special holding needs. This is an easy way to make a jig for odd shaped parts.

 Keep an extra set on hand!

Stock # 1051 Only...$8.75

Full Circle soft jaw set.... Works perfect for round stock and can be machined to hold odd shapes or to perform as a jig.

 Stock # 1052

   Only...$7.69

4 Jaw SELF CENTERING scroll Chuck. 3-1/4" Dia. 3/4-16 threaded mount, Steel Body with reversible aluminum soft jaws.

Stock # 1060

Retail... $72.40      Only...$71.99

0 to 1/4" Jacobs drill chuck, industrial quality.
3/8-24 thread to fit the drill arbor.

Stock # 1090

Only...$36.95

Stock # 1091

Only...$10.19

1/16" to 3/8" Jacobs drill chuck, commercial quality. 3/8-24 thread to fit drill arbor.

Stock # 1092 

Only...$10.19

1/8" to 1/2" Jacobs drill chuck,Commercial quality. 3/8-24 thread to fit drill arbor

Stock #1093

Only...$18.50

Slitting Saw Arbor! Screws directly onto lathe spindle. (Blade Not Included)Wrench included.

Stock # 1110

Only...$5.49

High speed steel slitting saw blade. .032" x 2-1/2" diameter for arbor above... (Arbor Not Included)

Stock # 1111  Blade Only.

Only...$12.59

ER STYLE  Slitting Saw Arbor.

Use This Arbor If You Have The ER Spindle Or Need An Arbor That Will Fit In Any 3/8" Collet.

# 1110ER

Only...$5.49

Grinding Wheel Arbor...NICE!
Screws directly onto lathe spindle. Stock

# 1120

Only...$6.19

ER-16 Collet Set These collets fit only the ER-16 spindles. A great set of 6 collets in sizes : 1/16, 1/8, 3/16, 1/4, 5/16, 3/8.

Each ER collet has a "Range" of tool sizes it will accept. This allows you to use a huge selection of tooling. A "Must Have" for any serious machine owner.

Order Yours Now......Stock # 1040-ER       Only... $55.50

A vise is pure necessity when doing milling work. This Taig vise is perfect for holding material. Convenient crank style handle! Great accessory for any mill.  Opens to 2-1/8" and the jaws are 2" Wide.

Stock # 2225     Only....$31.05

Grinding Wheel Set...Fits # 1120 Arbor Above....

Stock # 1122

Only...$6.99

Drill Chuck Arbor for Jacobs chucks listed above. Attaches Chucks to spindle. The smaller portion shown is 3/8-24 thread.

Stock # 1140

Only...$11.00

Drilling Tailstock. Lever operated with
5/8" offset with dead center. 3/8-24 thread.

Stock # 1150    Only...$38.99

Needle bearing center. Spring Loaded! Nice!

Stock # 1151 Only...$16.49

This Die Holder fits in the tailstock. Holds 13/16" & 1" Button Dies. Great for threading!

Stock # 1152

 Only...$15.99

"V" Belt # 3M 315 12-1/2" Flat Length.

Stock # 1159

Only...$7.89

Stock # 1160                 Only...$7.89

Included.

Stock # 1161         Only...$25.49

Six Step Pulley Set...2 per set 1/2" bore 3M 315 Belt Included.

Stock # 1162      Only...$25.49

Stock # 1170

Only...$4.50

Stock # 1171

Only...$4.99

T-Bar cut off tool.... Height Adjustable!

Stock # 1173

Only...$29.99

3-Point Steady Rest! NICE! 3/32" to 1-1/2" Capacity.

Stock # 1190

Only...$24.99

Stock # 1200         Only...$44.50

Radius Turner! Allows you to turn ball ends on shafts. Swings tool in an arc. Great!

Stock # 1210

Only...$19.99

Milling Attachment... makes your lathe work like a mill! Great attachment! Mounts directly on cross slide! 2" X 3-3/4" table.

Stock # 1220

Only...$62.75

Chuck Adapter. Adapts 3/4-16 threaded chuck to mill table.

This is great if you want to hold stock in a three or four jaw chuck for milling. Using this method can many times prevent spending time & material building a jig.

Stock # 1221

Only...$14.39

Fly Cutter. 1-1/4" to 2-1/2" diameter. 3/4-16 thread mount. Tool bit is included!

Stock # 1224

Only...$19.75

Stock # 1251

Only...$20.89

Complete Head Stock With ER 16 Spindle!

Now you can use 3/8" shank tools in your mill. Check out our Ultra Precision ER Collets! Stock # 200-00ER

View Shopping Cart Contents         Go To Cart Check Out

WE SHIP 95% OF ALL ORDERS WITHIN 24 HOURS!

We Carry American Made Micro Grain Carbide Cutting Tools. See Our End Mill Selection!

Our Shopping Cart is Secure & Safe!